Search results for "Power Module"
showing 10 items of 16 documents
Partial discharge of gel insulated high voltage power modules subjected to unconventional voltage waveforms
2016
Performances and duration of the new generation of high voltage power electronic components are dependent on dielectric materials aim to insulating their internal terminals. The presence of defects, some due to faults generated during the manufacturing process, but also due to the internal design of layers and connections, can cause local enhancements of electric field and consequently possible activity of partial discharges phenomena or other effects (aging, tracking) that may result in reduction of device reliability. Furthermore, the usage of unconventional voltage waveforms, like square waves or pulse width modulated waves, additionally increases the electrical aging of the insulation s…
Experimental test on a Contactless Power Transfer system
2014
Contactless Power Transfer (CPT) is an ever-growing technology in automotive market, due to the significant improvement brought by it to battery charging operation in terms of safety and comfort. CPT is based on inductive coupling between two coils, so that power cords can be avoided for vehicles battery charging and an important contribution towards a smarter mobility can arise. In this paper, a CPT prototype for E-bike is proposed. Magnetic design and power electronics system are described. Experimental results deriving from laboratory tests are presented and power efficiency of the system is addressed.
Measurements methodology for the reliability evaluation of intelligent power modules
2014
The paper describes a measurement methodology for the reliability evaluation of new intelligent power electronics modules (IPMs). In particular, the evaluation of the IPMs immunity to radio frequency conducted disturbances has been performed, at different operating thermal conditions, designing a suitable measurement set up in a shielded room. Moreover, the thermal performances of the devices have been analyzed, setting up a proper experimental test bench. The measurements procedures are detailed described. © 2014 IEEE.
Power quality effects on the measurement of reactive power in three-phase power systems in the light of the IEEE Standard 1459–2000.
2007
Reactive power is a very important quantity in electric power systems since it affects the efficiency of these systems. Also, capacitive loads can produce over-voltages in electric transformers by Ferranti effect, which produces bad power quality, so it is necessary to measure the reactive power correctly. In this paper reactive phenomena in three-phase power systems with unbalanced voltages are expressed and measured in the light of the IEEE Std 1459-2000. For analyzing the reactive phenomena the positive-sequence fundamental frequency instantaneous reactive power is used. By comparing the expressions of this instantaneous power in three-phase systems with unbalanced voltages with those co…
Electric and magnetic emission in near field region and thermal behaviour of power module for photovoltaic application
2015
The new power module, characterized by high power density, miniaturization of packages and layout and high frequency switching, are increasingly used in the field of in automotive, aircraft industry and for Distributed Generation (DG) connected to smart grid. To guarantee the reliability and safety of these systems, the electromagnetic compatibility (EMC) and thermal behavior, have to be carefully considered for these appliances. This paper describes a measurement methodology to characterize the electromagnetic emissions in near field zone produced by a PM prototype and its thermal behavior. In particular, the electric and magnetic fields, in the near field region in the frequency range 9kH…
High-Frequency Experimental Characterization and Modeling of Six Pack IGBTs Power Modules
2016
In this paper, a method to characterize the high-frequency (HF) behavior of six pack insulated gate bipolar transistors (IGBTs) power module (PM) is presented. The method is based on experimental measurements at the external pins of the device and it allows one to extract internal inductive and capacitive parasitic coupling without the knowledge of structural and physical parameters of the PM. The HF model of a six pack IGBTs PM has been developed, in the frequency range of 150 kHz-30 MHz, and it has been implemented in MATLAB environment. The method has been experimentally validated by comparing the frequency behavior of the PM with the simulated response. Moreover, the HF conducted distur…
High frequency modeling technique for three phase power electronics module
2015
Nowadays, the high integrated power electronics modules (PMs), characterized by high speed, low loss and hard ware miniaturization, represent a new technology that meets the emerging demands of many applications, such us vehicle and home appliance, renewable energy sources in smart grid. The integration process and the high switching speeds increase the PM electromagnetic emissions that can create electromagnetic interference (EMI) with electric/electronic devices near the PMs. For this reason, electromagnetic compatibility (EMC) have to be carefully considered, yet in the design phase, to guarantee the reliability of PM systems. In this paper a method to develop a high frequency (HF) model…
Novel GaN Based Solid State Power Amplifiers, Results, Advances and Comparison with Vacuum Tubes Based Microwave Power Modules
2018
Power amplifiers based on vacuum tubes or solid state are key items in a number of systems. Solid state technology is growing up for some applications and it may be complementary to the vacuum technology. This paperwork presents SSPA operational principles and performance. The GaN technology available in the market, the technology roadmap, a comparison with the vacuum tubes are introduced
Optimal Design of an X-Band, Fully-Coaxial, Easily-Tunable Broadband Power Equalizer for a Microwave Power Module
2020
A microwave power module (MPM), which is a hybrid combination of a solid-state power amplifier (SSPA) as a driver and a traveling-wave tube amplifier (TWT) as the final high power stage, is a high-power device largely used for radar applications. A gain equalizer is often required to flatten the TWT output power gain owing to its big gain fluctuations over the operating frequency range. In this paper, the design of an X-band, fully-coaxial, easily-tunable broadband power equalizer for an MPM is presented. The structure is composed of a coaxial waveguide as the main transmission line and a coaxial cavity loaded with absorbing material as a resonant unit. Sensitivity analyses of the attenuati…
Power management of grid-connected photovoltaic inverter with storage battery
2011
With increased penetration of PV generation in the power grid, it becomes necessary to control the PV generation similar to the conventional power sources. Grid-connected PV systems equipped with storage batteries are capable of active power control. PV power generation can be either fed into the grid or stored in the battery. This paper presents a deterministic power management algorithm that uses closed-form approximations derived from analytical loss models. It can be configured to maximize the efficiency or the revenue in a liberalized electricity market. The battery controller emulates an optimum load-line in which the PV power is autonomously shared between the battery and the feed-in…